1.power supply for site instruments2.signal isolated transfer3.signal conversion4.signal allocation in many ways5.alarm driving
TENGCON TG6044 Pt100 1-1 isolators
1. Modular design, clamping structure
2.Plug-in wire terminal, independent power wire terminal,and availability of plugging with power for convenience of installation, wiring and maintenance.
3.Series with CE certificate
TG 6000 series is a kind of electrical interface equipment developed by our company which is applicable for non-explosion-proof areas and can be used to connect site instruments and control room. Through reliable power-input-output isolation, it can resolve the site interference of auto-control system and make sure the stability and reliability of the system.
1.Power requirement: 20~30VDC;
2.Power with general rated value: 24VDC;
3.Transmission error: 0.1 degree, 0.2 degree(temperature transmitters);
4.T emperature drift: Superior to 0.1% FS/10°C(allowed temperature range);
5.Response time: < 1s (10~90%);
6.Stabilizing time: about 3~5s;
7.Current output load: 4~20mA, ≤5 50Ω;
8.V oltage output inner impedance: inner resistance ≤5 00Ω;
9.Dielectric strength (among input/output/power supply/instrument housing and wire terminals): ≤5 00Ω;
10.Insulation resistance (among power supply/input/output): ≥1 00MΩ;
11.Operating temperature range: -20~+60°C;
12.Shipping and storage temperature range: -40~+80°C;
13.Operating humidity allowed: 5~95%RH (no condensation);
14.Operating aTGospheric pressure: 80~106KPa ;
15.Electromagnetic compatibility: in accord with 89/336/EEC, IEC/EN 61000;
16.Protection grade: IP20 ;
17.Housing material: PC+ABS;
18.Installation: 35mm standard rail clamping installation;
19.Cable in use: 0.5~2.5mm wire;
20.Dimension: Width × h eight × l ength = 16× 116× 110 (mm);
21.Weight: about 110g~120g;
Introduction. Main T echnical Specification
Power supply isolator Supplies isolated direct current power for site transmitter, input 4~20 mA current signal from the transmitter , and outputs DC current or voltage signal to the control system or other instrument units after isolation and anti-interference.
The power supply isolator adopts independent DC power supply with power-input-output isolated.
P ower supplyPower supply: 20~30VDC
Current consumption (when 24VDC is supplying):
< 45mA (single-channel)
< 60mA (single-channel, dual-output)
< 70mA (single-channel, tri-output)
Input signal: 4~20mA direct current signal of transmitter
Input impedance: 50Ω (single channel, single channel, dual-output);
Supply voltage for transmitter: ≥ 16V (Power≥ 22VDC)
Maximum input current: About 24mA
Output current: 4~20mA; 0~20mA; 0~10mA; other specified current
Output voltage: 1~5V; 0~5V; 0~10V; other specified voltage
Allowed output load: 0~550 Ω (Power ≥2 2VDC at full load of 550Ω)
Voltage output impedance: ≤5 00Ω
Output ripple: < 10mVp-p
G eneral technical parameters
Transmission error: ± 0.1%
T emperature drift: ± 0.015% / °C
Startup response time: < 1s (10~90%)
Power change error: ± 0.1% (voltage scope 20~30VDC)
Dielectric strength: 1.5KV, 1 min, 50Hz among input- output- power
Insulation resistance: ≥ 1 00MΩ/500VDC among input- output- power
Operating temperature range: -20~+ 60°C
Dimension: Width× h eight × l ength = 16× 1 16 × 1 10 (mm)
About us: Beijing Tengcontrol Technology Limited Company
Rely on the hardware, software and network technique, Tengcon Technology devoted to manufacture industrial automation core products and systems with more than 30%of employee are focus in Research & Development. Tengcon has deep and wide experience in various signal acquisition, especially on electric signal acquisition, and also, familiars with all main protocol like MODBUS, IEC8705, PROFIBUS DP, CAN, PROFINET etc., and knows the ropes of IEC61131 and technology of Programmable Logic Controller development as well as IEEE1588 and Clock Synchronization Technology in Ethernet, we are also robust on antiinterference and lightning protection technology to ensure the reliability of every product delivered to customer.
Tengcon Technology proposed a new advanced concept of Complete Distributed Network Control System, in that the control system is constructed via absolutely new theory. It can be applied to construct the SCADA (Supervisory Control and Data Acquisition), PLC (Programmable Logic Controller) and DCS (Distributed Control System). Typical product were developed based on these is T9 series which were launched in market already. More than 100 thousands of product have been delivered to customers and got widely and good customer acceptance in past years.
All these products are being used in various industries in 18 counties. They showed strong reliability in different systems and wide environment include High Speed Rail, oil and gas field, power monitor and control system, kind of automatic production line, Building Management System,city lighting control system, vehicle monitoring, agricultural farms etc. we are keeping to develop and provide first class of product to all the customer in worldwide.