Tengcon Tg6053 One Input / Two Output Signal Isolator

Tengcon TG6053 One Input / Two Output  Signal Isolator


Specifications
 
1.power supply for site instruments
2.signal isolated transfer
3.signal conversion
4.signal allocation in many ways
5.alarm driving 


 
TENGCON TG6053 0-10V signal isolation
 
1. Modular design, clamping structure
2.Plug-in wire terminal, independent power wire terminal,and availability of plugging with power for convenience of installation, wiring and maintenance. 
3.Series with CE certificate
 
TG 6000 series is a kind of electrical interface equipment developed by our company which is applicable for non-explosion-proof areas and can be used to connect site instruments and control room. Through reliable power-input-output isolation, it can resolve the site interference of auto-control system and make sure the stability and reliability of the system.
 
Technical parameters
 
1.Power requirement: 20~30VDC;
2.Power with general rated value: 24VDC;
3.Transmission error: 0.1 degree, 0.2 degree(temperature transmitters);
4.T emperature drift: Superior to 0.1% FS/10°C(allowed temperature range);
5.Response time: < 1s (10~90%);
6.Stabilizing time: about 3~5s;
7.Current output load: 4~20mA, ≤5 50Ω;
8.V oltage output inner impedance: inner resistance ≤5 00Ω;
9.Dielectric strength (among input/output/power supply/instrument housing and wire terminals): ≤5 00Ω;
10.Insulation resistance (among power supply/input/output): ≥1 00MΩ;
11.Operating temperature range: -20~+60°C;
12.Shipping and storage temperature range: -40~+80°C;
13.Operating humidity allowed: 5~95%RH (no condensation);
14.Operating aTGospheric pressure: 80~106KPa ;
15.Electromagnetic compatibility: in accord with 89/336/EEC, IEC/EN 61000;
16.Protection grade: IP20 ;
17.Housing material: PC+ABS;
18.Installation: 35mm standard rail clamping installation;
19.Cable in use: 0.5~2.5mm wire;
20.Dimension: Width × h eight × l ength = 16× 116× 110 (mm);
21.Weight: about 110g~120g;
 
Product structure



Dimension diagram



Model selection


Introduction.  Main Technical Specification
 
DC signal repeater isolator
Inputs DC signal of various equipments, and outputs DC current or voltage signal to control system or other instruments after isolation and interference.
This DC signal repeater isolator adopts independent DC power supply with power-input-output isolated.
 
E lectric supply
Power voltage: 20~30VDC
Power indicator: Power LED lights on: Green
Current consumption (24VDC power supply): < 25mA (single-channel)
                                                                                   < 45mA  (single-channel, dual-output)
                                                                                   < 45mA  (single-channel, tri-output)
                                                                                   < 50mA  (dual-channel, dual-output)
 
I nput
Input current: 4~20mA; 0~20mA; 0~10mA; other specified current
Input voltage: 1~5V; 0~5V; 0~10V; other specified voltage
Input impedance: Current input 50Ω; voltage input ≥500KΩ
 
O utput
Output current: 4~20mA; 0~20mA; 0~10mA; other specified current
Output voltage: 1~5V; 0~5V; 0~10V; other specified voltage
Allowed load current: 0~550Ω (Power ≥2 2VDC at full load of 550Ω)
Voltage output impedance: ≤ 500Ω
Output ripple: < 10mVp-p
 
G eneral technical parameters
Transmission error: ± 0.1%
T emperature drift: ± 0.015% / °C(10~90%)
Power change error: (voltage scope: 20~30VDC)
Dielectric strength: Input-output-power 1.5KV, 1min, 50Hz
Insulation resistance: Input-output-power ≥ 100MΩ/500VDC
Operating temperature: -20~+60°C
Dimension: Width × h eight × l ength = 16× 116× 110(mm)
 

About us: Beijing Tengcontrol Technology Limited Company

Rely on the hardware, software and network technique, Tengcon Technology devoted to manufacture industrial automation core products and systems with more than 30%of employee are focus in Research & Development. Tengcon has deep and wide experience in various signal acquisition, especially on electric signal acquisition, and also, familiars with all main protocol like MODBUS, IEC8705, PROFIBUS DP, CAN, PROFINET etc., and knows the ropes of IEC61131 and technology of Programmable Logic Controller development as well as IEEE1588 and Clock Synchronization Technology in Ethernet, we are also robust on antiinterference and lightning protection technology to ensure the reliability of every product delivered to customer.

Tengcon Technology proposed a new advanced concept of Complete Distributed Network Control System, in that the control system is constructed via absolutely new theory. It can be applied to construct the SCADA (Supervisory Control and Data Acquisition), PLC (Programmable Logic Controller) and DCS (Distributed Control System). Typical product were developed based on these is T9 series which were launched in market already. More than 100 thousands of product have been delivered to customers and got widely and good customer acceptance in past years. 

All these products are being used in various industries in 18 counties. They showed strong reliability in different systems and wide environment include High Speed Rail, oil and gas field, power monitor and control system, kind of automatic production line, Building Management System,city lighting control system, vehicle monitoring, agricultural farms etc. we are keeping to develop and provide first class of product to all the customer in worldwide.